How to Program Channels

To program channels into your TV, the process can vary depending on your setup:


Using a Cable or Satellite box:

If you have a cable or satellite box, you do not need to program channels on your TV. Instead, you'll use the remote control provided by your cable provider to navigate channels.


Using a Streaming Device:

If you're using a streaming device like Roku, Apple TV, or Amazon Fire Stick, you won't program channels on your TV directly. Instead, you'll install apps or channels on your streaming device and access content through them.


Using an HD Antenna:

If you're using an HD antenna, you'll need to program channels directly into your TV.


Models TC-32A410, TC-39A410, TC-50A410

  1. Press [MENU].
  2. Press [▼] or [▲] to select "TV" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable Signal" and press right arrow to change to "Antenna" if setup up to off air antenna signal or select "Cable" if your signal setup is directly with a cable service provider without a cable box.
  4. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  5. Scanning starts.
    • The TV automatically searches and adds available channels to the memory.
    • After the scan is completed, all previously saved channels will be erased.
    • If you would like to cancel the scanning process press [RETURN].

Refer to your models operating instructions for more programming information.

Models TC-39AS530, TC-50AS530, TC-55AS530, TC-60AS530, TC-42AS630, TC-50AS630, TC-60AS630


  1. Press the [MENU] button on the TV remote.
    null Image varies by model

  2. Press the [▼] arrow down on the TV remote until "Setup" the Wrench icon is highlighted.
    null Image varies by model

  3. Press the [OK] button.
  4. Press the [▼] arrow on the TV remote until"ANT/Cable setup" is highlighted.
    null Image varies by model

  5. Press the [▼] arrow on the TV remote until "Auto program" is highlighted.
    null Image varies by model

  6. Press the [▼] arrow on the TV remote to select the desired scan mode.
  7. Press the [OK] button to start scanning.
    null Image varies by model

  8. Allow the status bar to reach 100%. Refrain from pressing any buttons on the TV or the TV remote during this process.
    null Image varies by model

  9. Press the [OK] button on the TV remote to select "Apply".
    null Image varies by model

  10. Any channels that were found during the channel scan can now be viewed when the TV is in the ANT/Cable or TV input.

Refer to your models operating instructions for more programming information.

Models TC-55AS800, TC-60AS800

Models TC-50CX600

Models TC-50GX700, TC-58GX700, TC-65GX700

  1. Press the [MENU] button on the TV remote.
  2. Press the [▼] arrow on the TV remote until "Setup" or the Wrench icon is highlighted and press [OK].
  3. Press the [▼] arrow on the TV remote until "ANT/Cable setup" or "ANTENNA/Cable setup"is highlighted and press [OK].
  4. Select "ANTENNA/Cable signal" and set to "Antenna" if setup up to off air antenna signal or select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Select "Auto program" and set to "All channels" or "Digital only" and press [OK].
  6. Allow the status bar to reach 100%. Refrain from pressing any buttons on the TV or the TV remote during this process.
  7. Once completed press the [OK] button on the TV remote to confirm and Apply the channels.
  8. Any channels that were found during the channel scan can now be viewed when the TV is in the ANT/Cable or TV input.

Refer to your models operating instructions for more programming information.

Models TC-26LX14, TC-32LX14


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-55GZ1000, TC-65GZ1000


Make sure the television is set to the "TV" input selection by pressing [INPUT] repeatedly until "TV' is highlighted and press [OK].

  1. Press the [MENU] button on the TV remote.
  2. Press the [▼] arrow to select "TV" and press [OK].
  3. Press the [▼] arrow to select "Tuner Mode" and press [OK].
  4. Press the [▼] arrow to select "Channel Scan" and press [OK].
  5. "All tuning data will be erased" displays on the TV. Press [OK] to start channel scan.
  6. "Status: scanning.." will display and a progress bar that displays the percentage completed.
  7. Once completed "Status: Scan Complete" is dispayed with the number of Analog and digital channels it has found.
  8. Press [RETURN] to go back to the previous menu.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-55GZ2000, TC-65GZ2000


Make sure the television is set to the "TV" input selection by pressing [INPUT] repeatedly until "TV' is highlighted and press [OK].

  1. Press the [MENU] button on the TV remote.
  2. Press the [▼] arrow to select "TV" and press [OK].
  3. Press the [▼] arrow to select "Tuner Mode" and press [OK].
  4. Press the [▼] arrow to select "Channel Scan" and press [OK].
  5. "All tuning data will be erased" displays on the TV. Press [OK] to start channel scan.
  6. "Status: scanning.." will display and a progress bar that displays the percentage completed.
  7. Once completed "Status: Scan Complete" is dispayed with the number of Analog and digital channels it has found.
  8. Press [RETURN] to go back to the previous menu.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-L32C12


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-L32G1, TC-L37G1


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-L32S1, TC-L37S1


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-L26X1, TC-L32X1, TC-L37X1


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-P42C1, TC-P50C1


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-P42G10, TC-P46G10, TC-P50G10, TC-P54G10


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-P42G15, TC-P46G15, TC-P50G15


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-42PS14, T-50PS14, TC-54PS14


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

Models TC-42PX14, TC-50PX14


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

Models TC-P42S1, TC-P46S1, TC-P50S1, TC-P54S1, TC-P58S1, TC-P65S1


This Answer applies for most models, for more specific information refer to yout models operating instructions.

  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

Models TC-P42S60, TC-P50S60, TC-P55S60, TC-P60S60, TC-P65S60


Make sure the television is set to the "TV" input selection by pressing [INPUT] repeatedly until "TV' is highlighted and press [OK].

  1. Press the [MENU] button on the TV remote.
  2. Press the [▼] arrow to select "TV" and press [OK].
  3. Press the [▼] arrow to select "Tuner Mode" and press [OK].
  4. Press the [▼] arrow to select "Channel Scan" and press [OK].
  5. "All tuning data will be erased" displays on the TV. Press [OK] to start channel scan.
  6. "Status: scanning.." will display and a progress bar that displays the percentage completed.
  7. Once completed "Status: Scan Complete" is dispayed with the number of Analog and digital channels it has found.
  8. Press [RETURN] to go back to the previous menu.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-P42U1, TC-P46U1, TC-P50U1


This Answer applies for most models, for more specific information refer to yout models operating instructions.

  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

Models TC-P42X1, TC-P50X1


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-P50ST60, TC-P55ST60, TC-P60ST60, TC-P65ST60


Make sure the television is set to the "TV" input selection by pressing [INPUT] repeatedly until "TV' is highlighted and press [OK].

  1. Press the [MENU] button on the TV remote.
  2. Press the [▼] arrow to select "TV" and press [OK].
  3. Press the [▼] arrow to select "Tuner Mode" and press [OK].
  4. Press the [▼] arrow to select "Channel Scan" and press [OK].
  5. "All tuning data will be erased" displays on the TV. Press [OK] to start channel scan.
  6. "Status: scanning.." will display and a progress bar that displays the percentage completed.
  7. Once completed "Status: Scan Complete" is dispayed with the number of Analog and digital channels it has found.
  8. Press [RETURN] to go back to the previous menu.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-P50V10, TC-P54V10, TC-P58V10, TC-P65V10


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TC-P54Z1


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TH-50PE8


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

Models TH-50PX60


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Select "ANT in" and press right arrow to change to "Antenna" if setup up to off air antenna signal or  select "cable" if your signal setup is directly with a cable service provider without a cable box.
  5. Press [▼] (down arrow) to select "Auto Program" and press [OK].
  6. Select a scanning mode by pressing [▼] (down arrow) to select "All channels", or "Digital only" and press [OK].
  7. After the scanning is completed, select “Apply” and press [OK]. 
     

Note:

All previously saved channels are erased


Manual program

If you want to set channels manually follow the steps above from step 1 through 6.

  1. For step 7 select "Edit" and press [OK].
  2. Using the arrows select the item to be edited (ei "Caption", "Favourite" or "Add".) and press [OK].
    • To proceed to next page press [G] (green) button.
    • To go back to the previous page press [R] (red) button.

Note:
To cancel the Edit function use the arrows to go up to select "Cancel" and press [OK].
"Changes will be lost.Continue?" will display. Select "yes' and press [OK]. 


Signal meter (Check signal strength)


Check the signal strength if an interference is found or freezing occurs on a digital image.

If the signal is weak, check the antenna.


  1. Press [Menu].
  2. Press [▼] or [▲] to select "Setup" and press [OK].
  3. Press [▼] or [▲] to select "ANT/Cable setup" and press [OK]. 
  4. Confirm that "ANT in" has the word "Antenna" beside it.
  5. Press [▼] or [▲] to select "Signal Meter" and press [OK].
  6. To check the signal strength of a specific channel press the number keypad to enter the channel number or press the [►] (right arrow) to chnage the channel to the one you would liek to verify the signal for.

If no problem is found, consult your local dealer.


Note:

  • The signal meter is not available if “Cable” is selected in “ANT in
  • Available only for digital antenna channels.

This Answer applies for most models, for more specific information refer to yout models operating instructions.

©2024 Panasonic USA All rights reserved.