How to use the Radio features on a Panasonic Audio System
Panasonic Audio products with Radio function allow you to tune stations manually, save favorite stations, change the sound quality for best reception, along with other radio features.
The features available and the programming steps vary by model.
Select your model from the drop down list below for specific
programming. If your model is not listed Refer to your models Operating
Manual for the specific procedure.
RC-7200
- Press the [RADIO] button.
- Select the desired Radio Band. The Radio Band selector switch is located on the right side of the unit. Band options are FM ST, Mono and AM.
- Adjust the station by rotating the [TUNING] dial. The Tuning dial is located below the Radio Band selector switch.
- To turn the Radio off press the [OFF] button.
View the Operating Manual for RC-7200 for more Radio functions and features.
RF-2400
- Set [OFF/BAND] switch to FM or AM.
- When FM is selected the FM indicator turns orange.
- When AM is selected the AM indicator turns orange.
- Adjust the station by rotating the [TUNING] dial.
- To turn the Radio off slide the [OFF/BAND] switch to OFF. The OFF indicator turns orange.
View the Operating Manual for RF-2400 for more Radio functions and features.
RX-D550
You can preset up to 30 FM channels.
Channel 1 to 5 will be set under [1] to [5] on this unit
Preparation
- Extend the antenna.
- Turn the unit on.
- On the remote press the [SELECT] button repeatedly to select "FM".
- Alternatively, on the unit, press [FM]
Presetting stations automatically
- Complete the Preparation instructions described above.
- Press [PLAY MENU] to select “A.PRESET”.
- Press the arrow up ▲ or down ▼ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency (“FM 87.9” or “FM 87.5”).
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
View the Operating Manual for RX-D550 for more Radio functions and features.
Listening to a preset channel
- Complete the Preparation instructions described above.
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select the channel.
You can select channel 1 to 5 by pressing one of [1] to [5] on the unit.
View the Operating Manual for RX-D550 for more Radio functions and features.
Manual tuning
- Complete the Preparation instructions described above.
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
View the Operating Manual for RX-D550 for more Radio functions and features.
Presetting stations manually
- Complete the Preparation instructions described above.
- While listening to a station press [OK].
- Press the arrow up ▲ or down ▼ to select the channel and then press [OK].
Do steps 1 through 2 again to preset more stations.
A station previously stored is overwritten when another station is stored in the same channel preset.
View the Operating Manual for RX-D550 for more Radio functions and features.
Changing the stations stored under [1] to [5]
On the main unit
- Complete the Preparation instructions described above.
- While listening to a station press and hold one of the 1 - 5 buttons until "P1, P2, P3, P4 or P5"" appears on the display.
- Press the arrow up ▲ or down ▼ to select the channel and then press [OK].
When you change the stations stored under [1] to [5], channel 1 to 5 are also changed to the same corresponding stations.
View the Operating Manual for RX-D550 for more Radio functions and features.
SC-AKX14
Manual tuning
- Press [RADIO] to select “FM or AM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
View the Operating Manual for SC-AKX14 for more Radio functions and features.
Improving the Radio sound quality
When "FM" is selected
- Press [RADIO] to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
When "AM" is selected
- Press [RADIO] to select “B.PROOF”.
- Press the arrow left ◄ or right ► to select “BP 1" or “BP 2" and then press [OK].
View the Operating Manual for SC-AKX14 for more Radio functions and features.
Memory presetting
30 FM and 15 AM stations can be preset.
Automatic presetting
- Press [RADIO] to select “FM or AM”.
- Press [OK] to select “LOWEST” or “CURRENT” frequency.
- Press [AUTO PRESET] to start presetting.
- To cancel, press the Stop [■] button.
Manual presetting
- Press [RADIO] to select “FM or AM”.
- Press the rewind or fast forward button to tune in the station.
- Press [PROGRAM].
- Press the numeric buttons to select a preset number.
- Do steps 1 through 4 again to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-AKX14 for more Radio functions and features.
Selecting a preset station
- Press [RADIO] to select “FM or AM”.
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-AKX14 for more Radio functions and features.
SC-AKX640
Manual tuning
Using the Remote control
- Press [RADIO] to select “FM or AM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
Using the Main Unit
- Press [RADIO] to select “FM or AM”.
- Press [TUNE MODE] to select “MANUAL”.
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-AKX640 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM and 15 AM radio stations
Automatic presetting
- Press [RADIO] to select “FM or AM”.
- Press [AUTO
PRESET] to select “LOWEST” or “CURRENT”
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- Press [OK] to start presetting. The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Manual presetting
- Press [RADIO] to select “FM or AM”.
- Press the rewind or fast forward button to tune in the station.
- Press [OK].
- Press the numeric buttons to select a preset number.
- Do steps 1 through 4 again to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-AKX640 for more Radio functions and features.
Selecting a preset station
Using the remote control
- Press [RADIO] to select “FM or AM”.
- Press the Skip back or Skip forward button to select a preset station.
Using the Main Unit
- Press [RADIO] to select “FM or AM”.
- Press [TUNE MODE] to select “PRESET”.
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-AKX640 for more Radio functions and features.
Improving the sound quality
When "FM" is selected
- Press [PLAY MENU] to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
When "AM" is selected
- Press [PLAY MENU] to select “B.PROOF”.
- Press the arrow left ◄ or right ► to select the setting that provides the best reception and then press [OK].
View the Operating Manual for SC-AKX640 for more Radio functions and features.
SC-HC200
Manual tuning
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
View the Operating Manual for SC-HC200 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] to select “A.PRESET”.
- Press the arrow up ▲ or down ▼ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Manual Presetting
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
- Press [OK].
- Press the arrow up ▲ or down ▼ to select a preset number and then press [OK].
- Repeat steps 3 to 6 to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-HC200 for more Radio functions and features.
Selecting a preset station
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-HC200 for more Radio functions and features.
Improving the sound quality
- Press the [RADIO] button to select "FM".
- Press the [PLAY MENU] button repeatedly to select “FM Mode”.
- Press the arrow up ▲ or down ▼ to select “MONO” and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-HC200 for more Radio functions and features.
SC-HC25
Manual tuning
- Press [RADIO] to select “FM or AM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
View the Operating Manual for SC-HC25 for more Radio functions and features.
Memory presetting
30 FM and 15 AM stations can be preset.
Automatic presetting
- Press [RADIO] to select “FM or AM”.
- Press [OK] to select “LOWEST” or “CURRENT” frequency.
- Press [RADIO MENU] to select “A.PRESET” and then press [OK].
- “START”is shown, press [OK] to start presetting.
Manual presetting
- Press [RADIO] to select “FM or AM”.
- Press the rewind or fast forward button to tune in the station.
- Press [PROGRAM].
- Press the numeric buttons to select a preset number.
- Do steps 1 through 4 again to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-HC25 for more Radio functions and features.
Selecting a preset station
Using the remote control
- Press [RADIO] to select “FM or AM”.
- Press the numeric buttons, or Press the Skip back or Skip forward button to select a preset station.
Using the Main Unit
- Press [RADIO] to select “FM or AM”.
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-HC25 for more Radio functions and features.
Improving the sound quality
When "FM" is selected
- Press [RADIO MENU] to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
When "AM" is selected
- Using the remote control Press [RADIO MENU] to select “B.PROOF”.
- Press the arrow left ◄ or right ► to select “BP 1" or “BP 2" and then press [OK].
View the Operating Manual for SC-HC25 for more Radio functions and features.
SC-HC295
Manual tuning
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
View the Operating Manual for SC-HC295 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] to select “A.PRESET”.
- Press the arrow up ▲ or down ▼ to select “LOWEST” or “CURRENT” and then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Manual Presetting
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
- Press [OK].
- Press the arrow up ▲ or down ▼ to select a preset number and then press [OK].
- Repeat steps 3 to 6 to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-HC295 for more Radio functions and features.
Selecting a preset station
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-HC295 for more Radio functions and features.
Improving the sound quality
- Press the [RADIO] button to select "FM".
- Press the [PLAY MENU] button repeatedly to select “FM Mode”.
- Press the arrow up ▲ or down ▼ to select “MONO” and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-HC295 for more Radio functions and features.
SC-HC300
Manual tuning
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
View the Operating Manual for SC-HC300 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] to select “A.PRESET”.
- Press the arrow up ▲ or down ▼ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Manual Presetting
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
- Press [OK].
- Press the arrow up ▲ or down ▼ to select a preset number and then press [OK].
- Repeat steps 3 to 6 to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-HC300 for more Radio functions and features.
Selecting a preset station
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-HC300 for more Radio functions and features.
Improving the sound quality
- Press the [RADIO] button to select "FM".
- Press the [PLAY MENU] button repeatedly to select “FM Mode”.
- Press the arrow up ▲ or down ▼ to select “MONO” and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-HC300 for more Radio functions and features.
SC-HC400, SC-HC410
Preparation
- Make sure that the antenna is connected.
- Turn the unit on.
Manual tuning
- Press [RADIO] to select “FM”.
- Press the rewind or fast forward button to tune in the station.. To tune automatically, press and hold the button until the frequency starts changing quickly.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-HC400 for more Radio functions and features.
View the Operating Manual for SC-HC410 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO] button to select "FM".
- Press [RADIO MENU] to select “A.PRESET”.
- Press the arrow right ► or left ◄ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Presetting Stations Manually
- While listening to a station press [PROGRAM].
- Press the numeric buttons to select a preset number.
Do steps 1 through 2 again to preset more stations.
A station previously stored is overwritten when another station is stored in the same channel preset.
View the Operating Manual for SC-HC400 for more Radio functions and features.
View the Operating Manual for SC-HC410 for more Radio functions and features.
Selecting a preset station
- Press [RADIO] to select “FM”.
- Press the Skip back or Skip forward button to select a preset station.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-HC400 for more Radio functions and features.
View the Operating Manual for SC-HC410 for more Radio functions and features.
Changing the stations stored under [1] to [5]
Channel 1 to 5 will be set as the favorite stations under [FAVORITE] [1] to [5].
On the main unit
- While listening to a station press and hold one of the 1 - 5 buttons until "P1, P2, P3, P4 or P5"" appears on the display.
When you change the stations stored under [1] to [5], channel 1 to 5 are also changed to the same corresponding stations.
View the Operating Manual for SC-HC400 for more Radio functions and features.
View the Operating Manual for SC-HC410 for more Radio functions and features.
SC-PM270K, SC-PM270PP
Manual tuning
- Press [PLAY MENU] repeatedly to select “TUNEMODE”.
- Press up down arrow to select "MANUAL" and press OK.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly. "STEREO" is shown when a tereo broadcast is being received.
View the Operating Manual for SC-PM270 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [PLAY MENU] button to select "A.PRESET".
- Press the arrow Up or arrow down to select “LOWEST” or “CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Presetting Stations Manually
- While listening to a station press [PLAY MENU] repeatedly to select "TUNEMODE".
- Press the up arrow or down arrow to select "MANUAL".
- Press or button to tune in to the station.
- Press OK
- Press Up arrow or down arrow to select preset number and then press OK.
Do steps 3 through 5 again to preset more stations.
The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-PM270 for more Radio functions and features.
Selecting a preset station
- Press [PLAY MENU] to select “TUNEMODE”.
- Press up arrow or down arrow to select "PRESET" and then press OK.
- Press the or button to select a preset station.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-PM270 for more Radio functions and features.
Improving the sound quality
- Press [PLAY MENU] repeatedly to select “FM Mode”.
- Press the arrow up or down arrow to select
“MONO" and then
press [OK].
To memorize the setting Continue with step 4 of “Manual presetting".
Checking the signal status
- Press DISPLAY
FM ---- The FM signal is weak. The system is not tuned in to a station.
FM ST The FM signal is in Stereo.
FM MONO "MONO" is selected as the "FM MODE". The FM signal is in monaural.
FM allocation setting
This system can also receive FM broadcasts allocated in 0.1 MHz steps.
- Press RADIO.
- Press and hold SELECTOR on the main unit.
After a few seconds, the display panel shows the current minimum radio frequency. Release the button when the minimum frequency changes.- To go back to the initial setting, do the above steps again.
- Preset frequencies are erased after you change the setting.
SC-PMX150S
SC-PMX150S
Manual tuning
- Press [RADIO] to select “FM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-PMX150 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO] button to select "FM".
- Press [RADIO MENU] to select “A.PRESET”.
- Press the arrow right ► or left ◄ to select “LOWEST” or “CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Presetting Stations Manually
- While listening to a station press [PGM].
- Press the numeric buttons to select a preset number.
Do steps 1 through 2 again to preset more stations.
A station previously stored is overwritten when another station is stored in the same channel preset.
View the Operating Manual for SC-PMX150 for more Radio functions and features.
Selecting a preset station
- Press [RADIO] to select “FM”.
- Press the Skip back or Skip forward button to select a preset station.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-PMX150 for more Radio functions and features.
Improving the sound quality
- Press [RADIO MENU] repeatedly to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-PMX150 for more Radio functions and features.
SC-PMX80, SC-PMX800
Manual tuning
- Press [RADIO] to select “FM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-PMX800 for more Radio functions and features.
View the Operating Manual for SC-PMX80 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO] button to select "FM".
- Press [RADIO MENU] to select “A.PRESET”.
- Press the arrow right ► or left ◄ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Presetting Stations Manually
- While listening to a station press [PGM].
- Press the numeric buttons to select a preset number.
Do steps 1 through 2 again to preset more stations.
A station previously stored is overwritten when another station is stored in the same channel preset.
View the Operating Manual for SC-PMX800 for more Radio functions and features.
View the Operating Manual for SC-PMX80 for more Radio functions and features.
Selecting a preset station
- Press [RADIO] to select “FM”.
- Press the Skip back or Skip forward button to select a preset station.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-PMX800 for more Radio functions and features.
View the Operating Manual for SC-PMX80 for more Radio functions and features.
Improving the sound quality
- Press [RADIO MENU] repeatedly to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-PMX800 for more Radio functions and features.
View the Operating Manual for SC-PMX80 for more Radio functions and features.
SC-PMX9
Manual tuning
- Press [SELECTOR] repeatedly to select “FM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
View the Operating Manual for SC-PMX9 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [SELECTOR] button to select "FM".
- Press [RADIO MENU] to select “Auto Preset”.
- Press the arrow right ► or left ◄ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Presetting Stations Manually
- While listening to a station press [PROGRAM].
- Press the numeric buttons to select a preset number.
Do steps 1 through 2 again to preset more stations.
A station previously stored is overwritten when another station is stored in the same channel preset.
View the Operating Manual for SC-PMX9 for more Radio functions and features.
Selecting a preset station
- Press [SELECTOR] to select “FM”.
- Press the Skip back or Skip forward button to select a preset station.
On the unit
- Press [SELECTOR] repeatedly to select “RADIO".
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-PMX9 for more Radio functions and features.
Improving the sound quality
- Press [RADIO MENU] repeatedly to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-PMX9 for more Radio functions and features.
SC-PMX90
Manual tuning
- Press [RADIO, EXT-IN] repeatedly to select “FM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-PMX90 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO, EXT-IN] button repeatedly to select "FM".
- Press [RADIO MENU] to select “A.PRESET”.
- Press the arrow right ► or left ◄ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Presetting Stations Manually
- While listening to a station press [PROGRAM].
- Press the numeric buttons to select a preset number.
Do steps 1 through 2 again to preset more stations.
A station previously stored is overwritten when another station is stored in the same channel preset.
View the Operating Manual for SC-PMX90 for more Radio functions and features.
Selecting a preset station
- Press [RADIO, EXT-IN] repeatedly to select “FM”.
- Press the Skip back or Skip forward button to select a preset station.
On the unit
- Press [RADIO MENU] repeatedly to select “TUNE MODE".
- Press the arrow right ► or left ◄ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-PMX90 for more Radio functions and features.
Improving the sound quality
- Press [RADIO MENU] repeatedly to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-PMX90 for more Radio functions and features.
SC-UA3
Manual tuning
- Press [RADIO, EXT-IN] to select “FM”.
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
Using the unit
- Press the Stop [■] button to select “MANUAL”.
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-UA3 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] to select “A.PRESET”.
- Press the arrow up ▲ or down ▼ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Manual Presetting
- Press the [RADIO] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
- Press [OK].
- Press the arrow up ▲ or down ▼ to select a preset number and then press [OK].
- Repeat steps 3 to 6 to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-UA3 for more Radio functions and features.
Selecting a preset station
- Press [RADIO, EXT-IN] to select “FM”.
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
Using the unit
- Press the Stop [■] button to select “PRESET”.
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-UA3 for more Radio functions and features.
Improving the sound quality
- Press [RADIO MENU] repeatedly to select “FM Mode”.
- Press the arrow up ▲ or down ▼ to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-UA3 for more Radio functions and features.
SU-UA7
Manual tuning
- Press [RADIO, EXT-IN] repeatedly to select “FM”.
- Press the rewind or fast forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
Using the unit
- Press the Stop [■] button to select “MANUAL”.
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-UA7 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM radio stations
Automatic presetting
- Press [RADIO/EXT-IN] to select “FM”.
- Press [AUTO
PRESET] to select “LOWEST” or “CURRENT”
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- Press [OK] to start presetting. The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Manual presetting
- Press [RADIO/EXT-IN] to select “FM”.
- Press the rewind or fast forward button to tune in the station.
- Press [OK].
- Press the numeric buttons to select a preset number.
- Do steps 1 through 4 again to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-UA7 for more Radio functions and features.
Selecting a preset station
- Press [RADIO, EXT-IN] repeatedly to select “FM”.
- Press the numeric buttons, or pres the Skip back or Skip forward button to select a preset station.
Using the unit
- Press the Stop [■] button to select “PRESET”.
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-UA7 for more Radio functions and features.
Improving the sound quality
- Press [PLAY MENU] repeatedly to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-UA7 for more Radio functions and features.
SC-UX100
Manual tuning
- Press the [RADIO/AUX] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station. To tune automatically, press and hold the button until the frequency starts changing quickly.
Using the unit
- Press the Stop [■] button to select “MANUAL”.
- Press the Skip back or Skip forward button to tune in the station.
View the Operating Manual for SC-UX100 for more Radio functions and features.
Memory presetting
You can preset up to 30 FM stations.
Presetting stations automatically
- Press the [RADIO/AUX] button to select "FM".
- Press [PLAY MENU] to select “A.PRESET”.
- Press the arrow up ▲ or down ▼ to select
“LOWEST” or
“CURRENT” and
then press [OK].
- LOWEST: To begin auto preset with the lowest frequency.
- CURRENT: To begin auto preset with the current frequency.
- The tuner starts to preset all the stations it can receive into the channels in ascending order.
- To cancel, press the Stop [■] button.
Manual Presetting
- Press the [RADIO/AUX] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “MANUAL” and then press [OK].
- Press the Skip back or Skip forward button to tune in the station.
- Press [OK].
- Press the arrow up ▲ or down ▼ to select a preset number and then press [OK].
- Repeat steps 3 to 6 to preset more stations. The new station replaces any station that occupies the same preset number.
View the Operating Manual for SC-UX100 for more Radio functions and features.
Selecting a preset station
- Press the [RADIO/AUX] button to select "FM".
- Press [PLAY MENU] repeatedly to select “TUNE MODE”.
- Press the arrow up ▲ or down ▼ to select “PRESET” and then press [OK].
- Press the Skip back or Skip forward button to select a preset station.
Using the unit
- Press the Stop [■] button to select “PRESET”.
- Press the Skip back or Skip forward button to select a preset station.
View the Operating Manual for SC-UX100 for more Radio functions and features.
Improving the sound quality
- Press [PLAY MENU] repeatedly to select “FM Mode”.
- Press the arrow left ◄ or right ► to select “MONO" and then press [OK].
- To cancel select “Stereo". “MONO" is also cancelled when you change the frequency.
View the Operating Manual for SC-UX100 for more Radio functions and features.